Stihl 041 Av Farm Boss Specs

Stihl 041 AV Specifications And Manuals

Stihl 041 AV Specifications information for Stihl chainsaw 041AV. A PDF workshop manual, parts list and a carburetor manual can be found here in the manuals section or by using the website search. A question and answer repair forum for the Stihl 041 AV chainsaw can be located HERE

Stihl 041 AV Specifications Information

STIHL 041 FARM BOSS CHAINSAW SPECS INTRODUCTION The following STIHL 041 FARM BOSS CHAINSAW SPECS E-book start with Intro, Brief Session until the Index/Glossary page, read the table of content for. The STIHL 024 is the first chainsaw to be equipped with the automatically triggered Quickstop chain brake. The 024 is part of a “next generation” of STIHL professional saws that sets new benchmarks with an outstanding power to weight ratio, ergonomic design and high safety standards while being easy to use and maintain.

Specs

SERIES OR ASSEMBLY NUMBER: 1110
ENGINE DISPLACEMENT: 61ccm 93.72 cu. in.)
CYLINDER BORE: 44mm (1.73 in.)
PISTON STROKE: 40mm (1.57 in.)
CYLINDER TYPE: Aluminum with chrome plated bore
INTAKE METHOD: Piston ported
MANUFACTURER ADVERTISED H.P.: 5.5
WEIGHT: 16 lbs. with 13 in. bar & chain
CLUTCH: Centrifugal
DRIVE TYPE: Direct
CONSTRUCTION: Die cast magnesium
MAGNETO TYPE: Bosch
CARBURETOR:Tillotson HS-29A, B, C, D, HS-77A, B, C, HS-87A, HS-100A, HS-138A, HS-208A
MAJOR REPAIR KIT: RK-21HS for HS-87, HS100RK-23HS for HS-29, HS-77, HS-138, HS208
MINOR REPAIR KIT: DG-3HS/T for HS-87, HS100 DG-5HS/T for HS-29, HS-77, HS-138, HS-208
AIR FILTER SYSTEM: Nylon mesh element
STARTER TYPE:Stihl automatic rewind
OIL PUMP: Automatic
IGNITION TIMING: 0.095 to 0.102 in. before TDC
BREAKER POINT SETTING: 0.35 to 0.40mm (0.014 to 0.016 in.)
SPARK PLUG TYPE: Bosch WSR56F
SPARK PLUG GAP: 0.51mm (0.020 in.)
CRANKSHAFT MAIN BEARINGS: Ball
FUEL OIL RATIO: 40:1 with Stihl oil
RECOMMENDED FUEL OCTANE: Regular
MIX OIL SPECIFICATION: Stihl two-cycle chain saw mix oil
SHORTEST GUIDE BAR SUPPLIED: 33cm (13 in.)
LONGEST GUIDE BAR SUPPLIED: 63cm (25 in.)

  • Stihl 041 AV is probably one of the best chainsaws ever made. It has displacement of 61 cm3, cylinder bore 44 mm, piston stroke 40 mm, 4,0 PS@7500 rpm (5,5 PS@7500 rpm reported when tested by DIN.
  • Stihl 041 av manual pdf Sharpening and Maintenance of Saw Chains. Parts of the Chain Saw. Safety Precautions. Toyota 7fbcu18 Manual. View and Download STIHL 041 Farm Boss instruction. View and Download Stihl FS 44 owner's manual online. FS 44 Trimmer pdf manual download. Also for: 041, 041 farm boss, 024, 021, 023, 025. Description Stihl 041 FB.
  • Rebuilding the carb on a stihls 041 farm boss and showing how it works. Rebuilding the carb on a stihls 041 farm boss and showing how it works.

mowisme

LawnSite Senior Member
Stihl

Stihl 041 Av Farm Boss Specs

FarmStihl 041 Av Farm Boss Specs

Stihl 041 Farm Boss Specs

Stihl 041 farm boss specs

Stihl 041 Farm Boss Price

I picked up a used Stihl (70/80's) Farm Boss 041 Chainsaw. Looks very clean for older one but..fires up and only can keep running about 30 sec. It evebtually loads up with gas and dies! If I keep air cleaner off so carb is completely exposed..seems to run slightly better and longer. There is a constant 'spiting' of gas or 'mist' of it coming out of mouth of carb while trying to start? seems like flooding after 2 pulls. then if starts get it to clear for few seconds then starts to load up again? Here is what I've done: 1) new plug 2) complete carb clean several times..and all new gasket kit. 3) new point's (set at .015) 4) replaced fuel line from tank to carb and pulsating line from carb to case. 5) pulled line and filter up out of tank and inspected very close..looks perfect as well as screen in filter. I don't think it is fuel delivery problem as fuel spits out onto my hand (with air cleaner off) and seems flooded always. It had 'spark' before replacing points..and does now with new ones..I'm wonering if this sounds like 'seal' problem? I almost wondering if the 'chain oil' somehow seeping into case..saw what looked like oil in cylinder while tore down- seemed to thick to be gas/oil mix..? any Ideas?..getting into too much money on this for a used saw. Thanks- Geno